tolerance

Fault diagnosis of circuits with tolerance based on body and KNN method;

基于集团法和自组织神经网络的容差电路故障诊断(英文)

A Combining Genetic Algorithm With Simplex Method in Optimum Assignment for Circuit Component Tolerance;

GA混合参数寻优在电路参数容差分配中的应用

A new Fault Diagnosis Method of Subnetworks in Tolerance Analog Circuits;

容差模拟电路子网络级故障诊断的新方法

Throclgh loss function calculating the allowance ,thestandard tolerances of hole and shaft are defined.

用田口理论建立孔、轴配合的质量损失函数，给出配合的功能极限（用户容差）和用户损失的决定方法。

Using Genichi·Taguchi′s approach,this paper gives all formulas that are suited for calculating the allowances of mechanical parts′ non-fit measurements.

本文以质量损失函数为计算基础，得出零件非配合尺寸的容差计算公式。

After investigating and eaxmining the user s allowance, loss and factory s loss of the small diameter of inside thread and large diamtcer of outside thread respectively, the factory allowance of the small diameter of inside thread and large one of outside thread can be computed by using the loss function.

依据质量工程学的损失函数理论 ,建立紧固螺纹配合间隙的质量损失函数 ,推导出内、外螺纹中径的工厂容差的计算公式 ;最终的制造公差和精度等级按此计算值来查表选定。

The paper introduced the new method of optimal design of tolerance based on dimensional allowance in virtual assembly:Informational matrixes of conjugation are worked out according to rules.

提出了一种基于虚拟装配尺寸容差的公差优化设计新算法:由定义创建配合信息矩阵,并从矩阵中快速搜寻配合信息、生成装配尺寸链;依据田口品质损失理论,同时采用多元微分法或遗传算法的模拟求解法得到优化的装配公差。

An allowed difference in dimension of closely mating machine parts.

公差，容差机器配件的公差，容差

DIMENSIONS AND TOLERANCING PER ASME Y14.5

尺寸和容差参照ASME Y14.5

product target including safety margin

包括容差的建屋量指针

reference surface diameter tolerance

基准面直径容差 -光纤的

wet wash allowance

湿法选矿后的水分容差

Evaluation of Color-Difference Formulae Based on the Correlation Between Visual Tolerances and Hue Angles

基于视觉容差与色调角相关性的色差公式评价

Tolerances unless otherwise specified

除非另有说明,适用以下容差

margin of error

最大容许误差;最大允许误差;误差界限;误差量

acceptable deviation of controlled variable

控制变量的容许偏差

color tolerance computer

颜色容许误差计算机

bleed allowance

色浆渗化分线容许公差

an unacceptable level of inaccuracy

误差达无法容许的程度.

The film forgives errors in focusing.

这种胶卷容许调焦误差。

itance acceleration transducer

差容式加速度传感器

On the Question of Admissibility of Quadratic Estimators of Error Varuance in a Linear Model

线性模型中误差方差的二次估计的可容性

THE ADMISSIBILITY OF NON-HOMOGENE OUS ESTIMATE OF VARIANCE IN LINEAR MODEL

线性模型中误差方差的非齐次估计的可容许性

Effect of capacitance deviation on the supercapacitor energy storage module and solutions

容量偏差对超级电容储能的影响及解决方案

Approximate Calculation of Unbalance Protection on Differential Current Bridge of Large Capacity Capacitor Bank

大容量电容器组桥差不平衡电流保护近似计算