beam bending stress

Research of actuation characteristic of a curved cantilever electrostatic actuator;

弯曲悬臂梁静电执行器驱动特性的实验研究

With regard to transverse bending beam under complex stress state in plane,when different tension and compression modulus is introduced,the pole bending rigidity is a function of internal force so that the calculation of structural internal force becomes nonlinear problem.

对于处在平面复杂应力状态下的横力弯曲梁,当引入拉压不同模量后,结构内力计算成为非线性问题;对拉压不同模量横力弯曲梁提出计算假定,推导单元中和轴公式并构造了算法;通过实例计算对比分析不同模量与经典力学相同模量两种方法计算结果的差异,提出对该类结构计算的合理建议以及利用不同模量对结构进行优化的结论。

Finite element analysis on the bending stress for roller spur bevel gear based on ANSYS;

基于ANSYS的滚齿直齿圆锥齿轮弯曲应力有限元分析

Analysis of tooth root bending stress for spiral bevel gears;

弧齿锥齿轮齿根弯曲应力分析

Calculation of bending stress of steel-concrete composite beam considering slippage effect;

考虑滑移效应的钢—混凝土组合梁弯曲应力计算

The article anaylses the skew arch roofing s bend stress under symmetry and unsymmetrical loads,calculates the skew arch roofing critical load under the symmetry and unsymmetrical loads,the result indicates the skew arch roofing s resistance,and stability are sufficient for its use.

分析了在对称和非对称载荷作用下斜拱型屋面弯曲应力,计算了在对称载荷和非对称载荷作用下斜拱型屋面临界载荷。

This paper demonstrate the way how to measure and control D max -D min  of the pressure cylinder for its safe working,which is started with the circular additional bend stress which is caused by the non circularity of the pressure cylinder,then it points out a new method of controlling strength of the pressure cylinder.

从压力容器不圆度引起周向附加弯曲应力出发 ,推导出检测和控制不圆度值的方法 ,使其达到其安全工作的目的 ,为工业生产及检测部门提供依

This paper points out a proplem in《Mechanial Design of Forestry Engirieer-ing》Writted by Fu Wenfan that formula in calculating the bend stress of the hook.

本文指出了傅文范等著《森林工程机械设计》（绞盘机）中涉及到的关于吊钩钩身弯曲应力公式存在的问题，并根据有关理论，提出比较符合实际的计算吊钩钩身弯曲应力的公式。

Research of actuation characteristic of a curved cantilever electrostatic actuator

弯曲悬臂梁静电执行器驱动特性的实验研究

Bending behaviors of functionally gradient piezoelectric curved cantilever was studied.

研究了弯曲型梯度功能压电悬臂梁的弯曲特性。

Research on bending of the cantilever based on the principle of minimum potential energy

基于最小势能原理的悬臂梁弯曲研究

Hamiltonian system approach to bending problem of viscoelastic cantilever-beams

粘弹性悬臂梁弯曲变形的哈密顿体系方法

Bending deformation of microscale cantilever has been investigated using an atomic force microscope( AFM).

采用原子力显微镜测试了微悬臂梁构件的弯曲变形规律。

BOUNDARY INTEGRAL FORMULA FOR BENDING OF CLAMPED SEMI-INFINITE PLATE

悬臂半无限大板弯曲的边界积分公式

Study on Construction Control of Cantilever Erection Continuous Curved Girder Bridge;

悬臂拼装曲线连续梁桥施工控制研究

It is found that non-zero normal stresses exist in the gradient piezoelectric curved cantilever when the cantilever is subjected to an external voltage.

研究表明，当受外加电压作用时，弯曲型梯度压电悬臂梁中存在非零的应力。

Fourier analysis of bending of orthogonal anisotropic rectangular thin cantilever plate

正交各向异性矩形悬臂薄板弯曲的傅立叶分析

The pouring construction technology of small radius flat curve continuous steel bridge cantilever

小半径平弯曲线连续刚构桥悬臂浇筑施工技术

Specimen for surface crack growth by loading at cantilever bend and application

一种悬臂弯曲加载表面裂纹扩展试样及其应用

Experimental Investigation of the Model and Analysis on Curvilinear Bridge with Boxed Cross-section;

曲线箱梁桥悬臂施工模型试验研究与分析

Key Technology in Construction Control of Curved Bridge by Sectional Cantilever Form Traveler

曲线桥梁分段悬臂挂篮施工控制关键技术

Simulation Analysis and Curing Effect Research of Curved Continuous Rigid Frame Bridge during Cantilever Construction;

曲线连续刚构桥悬臂施工阶段的仿真分析及弯曲效应研究

Considering the difference of cantilever plate between the end and the middle of the concrete box bridge, the chief influence factor is studied.

考虑箱梁端部和跨中悬臂板根部的区别，研究了影响变厚度悬臂根部弯矩的主要因素。

overhung cold roll forming machine

悬臂辊式冷弯成型轧机

knee-braced bracket

拐弯托座，膝形悬臂托架

cantilever beam impact tester

悬臂梁式冲击试验机