cap bolt

Research of tightening technology for cylinder head bolt;

发动机缸盖螺栓拧紧工艺研究

According to the numerical simulation of heavy-duty diesel engine to raise power,two methods to assess the strength of cylinder head bolt,static calculation and fatigue stress check,are introduced.

结合大功率柴油机提升功率的数值计算工作,介绍了评估气缸盖螺栓强度的两种方法:静强度分析法和疲劳强度校核法。

This paper analyzed the chemical composition, metallurgical microstructure, macroscopical and microcosmic fracture appearance, mechanical performance and the received force circumstance of cylinder head bolt assembly.

分析了断裂缸盖螺栓的化学成分、金相组织、宏观及微观断口形貌,以及力学性能和螺栓装配受力情况,分析结果表明,由于缸盖螺栓表面存在硬化层而且外观质量不佳,螺栓发生脆性断裂,造成了发动机冲缸垫故障,并提出了改进措施。

Analysis on Fatigue Cracking of Cylinder Cap Bolt

缸盖螺栓接触损伤引发疲劳开裂分析

The Fuzzy Reliability Design about the Bolt-joint Set of Engine Bonnet

内燃机缸盖螺栓组联接的模糊可靠性设计

Effect of Bolt Hole Depth on Camshaft Bore of YZ4DE Diesel Engine

YZ4DE柴油机气缸盖螺栓沉孔深度对凸轮轴孔的影响

The cylinder head is attached to the block with high-tensile steel studs.

气缸盖与气缸体用高强度的钢螺栓缚连结。

New cylinder head bolts should be use

应使用新的汽缸头螺栓。

Remove the engine cylinder head bolts.

拆卸引擎汽缸头螺栓。

Remove bolts, nuts and washers attaching manifold to cylinder hea

拆下系附在汽缸头的螺栓，螺帽和垫圈。

cap-and-pin type insulator

帽盖穿心螺栓式绝缘子

Engine Cylinder Head Bolt Tightening Sequence

引擎汽缸头螺栓锁紧顺序

Tighten exhaust manifold to cylinder head bolts.

紧固排气岐管汽缸头螺栓。

Analysis on Fatigue Life to the Air Cylinder Bolt in Super High Pressure Compressor

超高压压缩机气缸螺栓疲劳寿命评估

Remove the relief valve cover bolts while holding the cover down.

边压住阀盖，边拆卸安全阀阀盖螺栓。

Stainless steel stuffing box hardware is standard (ie. bolts, gland studs, nuts, washers).

标准的金属密封不锈钢填料箱（如螺栓、填料压盖螺栓、螺母、垫圈）。

Reliability of Analysis of the Primary Cylinder s Bolt Joint in Flange of the Hydraulic Press;

液压机主工作缸法兰处螺栓联接的可靠性分析

Assessing the Residual Fatigue Life of the Cylinder Bolt in the Super Pressure Compressor;

超高压压缩机汽缸螺栓剩余疲劳寿命的评估

The Measuring Method & Application of Cylinder Bolts Extension for Assembling

汽轮机汽缸中分面螺栓伸长量测量方法及应用

Install the bolts attaching the end cap to the front fender.

安装连接末端端盖到前挡泥板的螺栓。

"Bolts,screws & nuts"

"螺栓,螺丝及螺帽"