housing

In this paper,some research on the optimization and parametric analysis of a ring-groove cylindrical shell structure were given out under lateral explosion impulsion and axial pressure.

基于有限元分析,以侧向爆炸冲击和轴向面力为载荷形式,对环向槽圆柱壳结构形式进行了大量的数值模拟计算,履行了参数分析,基于响应面法构造近似显式优化模型,采用MATLAB软件优化程序求解该模型,对各参数的组合进行了优化设计。

Study on the 3D heat transfer model of the aluminum reduction cell shells based on the method of simulation;

铝电解槽侧部槽壳散热三维仿真模型研究

The writer gives a systematical analysis on the cause of serious deformation of 186kA aluminum electrolytic pot shell and provides a specific reparation plan,which has made a satisfactory result.

针对186kA铝电解槽槽壳变形严重的情况,对其变形原因进行了认真地分析,并提出了具体的修复方案,取得了良好的效果。

The analysis of pot shell changing laws and cradle frame swelling laws is given by discussing the changing laws of caloric expanding pressure on the appearance of liner.

运用有限元软件AN SY S对300 kA铝电解槽焙烧启动过程一系列温度场下的热应力耦合场进行了数值计算,通过计算内衬外表面热膨胀压力,对槽壳变形和摇篮架工字梁上拱进行了分析,并讨论了内衬外表面热膨胀压力的变化规律,为铝电解槽焙烧启动过程仿真与优化提供了参考。

Report the measuring of aluminium pot shell swelling right after the pot start-up.

测量和记述了铝电解槽启动期间的槽壳上拱。

Numerical Study on Thermal-Elasto-Plastic and Creep Deformation of Aluminum Electrolytic Cell;

铝电解槽槽壳热弹塑性及蠕变有限元计算

Design of Web-based Temperature Monitoring System for Aluminum Reduction Cells

基于Web的铝电解槽槽壳温度监测系统设计

Research and Design of Online Temperature-Monitoring of Aluminium Cell Shell and Diagnosis of Cell Status System;

铝电解槽槽壳温度在线检测及槽况诊断系统的研究与设计

A groove around the cylinder of a bullet.

弹壳槽线一圈环绕着子弹的圆柱状凹槽

Performance and Application Research of Shell-and-tube Ice Storage Tank;

壳管式外融冰槽热工性能及应用研究

The Numerical Model of Original Shell in Grooved-Mold;

沟槽内壁结晶器初生坯壳的数学模型

Research and Application on the On-line Temperature Detection of Aluminum Cell Shell and the Cell Status Diagnosis Expert System;

铝电解槽糟壳温度在线检测与槽况诊断专家系统的研究与应用

Mount the drives in the case.

将软驱或IDE装置放入机壳中相对应的空槽中。

Position dome/reading lamp housing at headliner cavity.

将圆顶照明/阅读灯外壳定位于车顶蓬内衬槽中。

Slide and tap in reservoir retainer clips until tab locks to housing.

滑动并敲击贮油槽扣件夹，直至凸耳锁紧外壳。

Research on Fatigue Failure of Reverse Vaulted and Notched Thin Metallic Shell under Uniform Pressure;

均匀压力下反拱带槽金属薄壳的疲劳特性研究

Research on the Destruction Mechanism to Preventing and Curing Technology in the Thin Shell Aqueduct of Armored Concrete

钢筋混凝土薄壳渡槽破坏机理与防治对策研究

Processing of Radiator of Conical Mould of Picture Tube

探索彩色玻壳锥凸模模具散热槽电极的加工

Impact Analysis of the Ring Slot around the Bearing Shell of Top Rollers on Cot Telescoping Process

上罗拉轴承外壳环形槽对套制胶辊的影响分析

Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots.

修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。切勿清除在后主盖槽中的密封剂。

But as I told you, the main tanks are outside the real hull.

可是正如我已经告诉你的，主要的水槽都在真正的艇壳外面。

CHARACTERISTICS OF CARBONIFEROUS CRUSTAL MOVEMENTS IN NORTH XINJIANG WITH REFERENCE TO THE TIME OF GEOSYNCLINAL CLOSING

新疆北部石炭纪地壳运动特征兼论地槽区封闭时代

The Experimental Research of Alveolar Bone Regenerated by Compound Material of Carboxymethyl Chitosan Tricalcium Phosphate;

羧甲基壳聚糖-钙盐复合物诱导齿槽骨再生的实验研究