soaker

Analysis was made on countermeasures for leakage protection and sealing in different formations,and corresponding formulas and operating details were obtained through laboratory tests.

在现场调研的基础上,针对不同漏失地层的防漏堵漏对策进行了分析;通过室内试验评价得到对应的防漏堵漏配方与实施细则;在以ZK7-1孔为代表的多个钻孔展开现场试验,效果良好,可在该地区或国内类似地区进行推广。

Cementing technology of using leak protection and water shutoff drilling fluid in LIN 4-36X Well

林4-36X井防漏防窜水泥浆固井技术

It is adopted to improve mud's leak protection that adding mekralon into mud in the leaking layer.

针对漏失地层固井,采用聚丙烯纤维加入水泥浆中改善水泥浆的防漏性能,增加水泥石韧性。

The leak protection and toughness-reinforcement cement slurry,in which chaotic short fibres-F27A are the core materials,was developed to prevent the slurry leaking in cementing operations and the cement mantle brittle rupturing,i.

为解决油田复杂地层固井时的水泥浆漏失低返以及射孔和后续增产措施造成的水泥环脆裂(即二次窜流)问题,研制开发了以混杂短纤维为核心材料(F27A)的防漏增韧水泥浆体系,并对其防漏性能、水泥石的各种力学性能(抗折强度、抗冲击功和弹性模量)及水泥浆体系的工程性能进行了研究。

Several new drilling fluids abroad focused on lost circulation control and plugging,hole stability and in 2004 also appeared.

2004年,国外出现的钻井液新技术还包括防漏堵漏技术、井壁稳定技术和环境保护方面的技术。

Remover, Moldings C-4829

拆卸工具，嵌条C-4829

REAR HEADLINER TRIM MOLDING

后车顶蓬内衬装饰嵌条

Apply the molding to the windshield:

将嵌条应用至挡风玻璃：

REAR DOOR GLASS EXTERIOR MOLDING

后车门玻璃外观嵌条

The slot seam is a decorative seam.

嵌条缝是一种装饰缝。

A thin, flat molding used as separation between or ornamentation for larger moldings.

平缘用来隔开或装饰更大嵌条的扁平嵌条

Install beltline molding and weatherstrip seals.

安装装饰带嵌条及防水饰条密封。

The easiest form of inserting is that used for a piped seam.

镶嵌最简单的形式就是采用嵌条缝(夹紧缝)。

Snap molding down over top of retaining clips.

向下压紧嵌条至固定夹上方。

A wide vertical band in the center of an escutcheon.

垂直宽条在一个饰有纹章的盾的中心部分的一条较广的垂直嵌条

Starting at the forward end of the upper molding, force the molding onto the door panel flange and continue rearward until it is completely seated on the flange.

从上部嵌条的前末端开始，用力使嵌条到车门饰板上并且继续向后直到它完全固定在凸缘上。

Install liftgate opening (headliner) upper trim molding.

安装升降闸门开口（车顶蓬内衬）上装饰嵌条。

Remove liftgate opening (headliner) upper trim molding.

拆去升降闸门开口（车顶蓬内衬）上装饰嵌条。

For curved slot seams, both sides of the seam must be faced and underlay follows the same curve.

弧形嵌条缝,缝的两边必须对称,垫层的弧度相等。

A narrow border, molding, or fillet.

扁带饰窄条，装饰用嵌线或窄带

embedded stripe double-heterostructure laser

嵌入式条状双异质结构激光器

A thin, dressed rectangle of stone for facing walls.

整形块石嵌饰墙面的长条形琢石

Research on Embedded Controller for Oblique Cutting Machine Based on ARM;

基于ARM的嵌入式斜条机控制器的研究