cable assemble

Study on the new winding cable and its grounding system;

新型绕组电缆及其接地系统的研究

In order to analyze the heat phenomenon of high voltage linear motor in operation,the computation model of its stator and winding cable was built firstly.

为研究高压电缆绕组直线电机运行中可能出现的发热现象,建立了直线电机定子及绕组电缆的计算模型,用有限元法计算了电机在三相交流电作用下的涡流及电磁损耗分布,研究了绕组电缆有无金属屏蔽时电机内涡流分布的变化,并分析了涡流产生的热效应及其对电机运行带来的影响。

The new kind of high voltage motor and the characteristics of the winding cable are presented in this paper.

介绍了新型电缆绕组高压电机并分析了绕组电缆的结构及特性,为解决绕组电缆外半导电层局部温升过高的问题,首先利用ANSYS软件仿真分析外半导电层的电场和磁场耦合场,确定了温升与接地电流的关系,然后采用PowerSim软件研究了外半导电层电阻对系统的影响。

Design of connector process coaxial cable module;

一种TNC型射频连接器电缆组件的研制

This paper introduced the method to install the semi-rigid cable module,and described the conventional welding technology used to install the cable modules.

介绍半刚性电缆组件的装接方式,阐述半刚性电缆组件传统焊接工艺的方法,从焊接工艺对半刚性电缆组件可靠性的影响来分析引起电缆焊点开裂失效原因和解决措施,并对工艺过程加工方法和要求作了详细叙述。

Basing on the circuit model,which brought out in,a high frequency transient circuit model of cable windings is presented,in which the influence of the capacitance of outer semiconduct.

为了解交联聚乙烯(XLPE)电缆绕组变压器绕组外半导电层的对地电容对电缆绕组暂态特性的影响,改变试验绕组外半导电层对地电容进行对比试验,并基于前期仿真模型建立了考虑外半导电层对地电容影响的模型。

In this paper, a new PacketCable architecture framework of inter-domain communication is propounded on the basis of PCMM specification and PacketCable 1.

在分组电缆多媒体(PCMM)规范和分组电缆(PacketCable1。

Radio frequency and coaxial cable assemblies--Part 2-1: Sectional specification for flexible coaxial cable assemblies

GB/T15866-1995射频同轴电缆组件第2-1部分:柔软同轴电缆组件分规范

Radio frequency and coaxial cable assemblies--Part 3: Sectional specification for semi-flexible coaxial cable assemblies

GB/T16531-1996射频同轴电缆组件第3部分半柔软同轴电缆组件分规范

Radio frequency and coaxial cable assemblies--Part 4: Sectional specification for semi-rigid coaxial cable assemblies

GB/T15867-1995射频同轴电缆组件第4部分:半硬同轴电缆组件分规范

Electrical Length Definition for Cable Assembly

电缆组件中电气长度确定依据的探讨

The design shall incorporate provisions that prevent moisture from wicking through the cable assembly even in the event the cable jacket has been punctured.

这种设计应该配置相关物品,以防止电缆外壳被刺穿后导致潮气侵入电缆组件。

Radio-frequency and coaxial cable assemblies Part 1: Generic specification-General requirements and test methods

GB/T17738.1-1999射频同轴电缆组件第1部分:总规范一般要求和试验方法

Development of partial discharge detection systems for XLPE cables based on COM component technology

基于COM组件技术的XLPE电缆局放检测系统开发

hank of cable

电缆盘, 一盘电缆

Abstract: The measuring and monitor system of temperature of cable connection at TG No.5 power station, including its hardware component, theory, characteristic and software function, are introduced.

【摘要】绍了太钢五降压站分布式电缆中间头温度及水位监测系统的硬件组成、理、点及软件功能。

Le réseau souterrain à 20KV de Paris

巴黎20千伏配电网的电缆及其附件

The mian productions are:fibre optic cable、electronic device,etc.

主要产品有：光纤电缆、电子元件等。

Design of the Dies for Producing Segmented Conductors in Power Cables with the Software AutoCAD

用AutoCAD软件设计电力电缆瓦形导体模具

Ribbon cable: Flat plastic coated cable in which the lines lie parallel to each other.

带式电缆:在一组平等排列的电线，加上胶套而成的平坦电缆。

A group of pairs in a cable.

一条电缆中的一组双绞线。

The mian productions are: fibre optic cable、 electronic device, etc.

主要产品有：光纤电缆、子元件等。

Electrical Lofting(电气放样)： Application of program to ensure the reasonable arrangement of cables in vessel.

应用软件来确定电缆的准确走向。

Production: metal shaft, cable repair, metal accessories.

生产：金属槽管，电缆桥架，五金配件。

the Software System Design of Line Type Heat Cable Controller;

线型感温电缆控制器的软件系统设计