cam driver

This paper deduces the general solution for another kind of wedge differing from the wedge in paper [l] with the popularized dimension -analysis method in paper [l] proposed by the author.

本文用作者在文[1]中提出的推广的因次分析法推导了与文[1]中不同的另一类楔体形的通解。

Based on the author s work[1] and the generalized dimension-analysis method, the author improves and perfects the general solution for a kind of wedge with a concentrated load or distributed load which is inversely proportional to r on the boundary and the infinite plate with a small bole subjected to a concentrated load in the hole.

本文在笔者文［１］的基础上，再次用推广的因次分析法证明了楔形体顶端受集中力，边界上受有与ｒ成反比的面力以及带小孔无限大板在孔中受集中力一类楔形体的通解，完善了文［１］中关于边界上受有与ｒ成反比的面力的解答。

blade, for guillotine-type shears

铡刀式剪切机用刀片

She faced death calmly and unflinchingly before the enemy's chaff-cutter.

她在敌人铡刀前，视死如归，毫无惧色。

Standing in front of the hay cutter, He seems to start a journey to the paradise, laughing and saying, "I will be another hero/ tough guy in 20 years".

他站在铡刀前，竟然像快去天堂巡游一样一边大笑一边说：“老子20年后又是一条好汉。”

Virtual Design and Performance Study of Flywheel-type Cutterhead;

盘刀式铡草机切碎器的虚拟设计及其性能研究

21Unique risk may be called unsystematic risk, residual risk, specific risk, or diversifiable risk.

囟ǚ缦湛梢员怀莆?窍低撤缦铡⑹Ｓ喾缦铡⑻囟ǚ缦栈蛘呖煞稚⒎缦铡

Safety technical requirements for choppers

GB7681-1997铡草机安全技术要求

This Protocol shall be registered in accordance with the provisions of Article102 of the Charter of the United Nations.

?疽槎ㄊ橛σ勒铡读?瞎?苷隆返

The tuffaceous formation, isolated remnants, are about 200-250 ft thick.

凝灰岩构造的局部残存段的厚度约为200-250?铡?

Peter stayed in Joppa for some time with a tanner named Simon.

撕蟊说迷谠寂烈桓鱿跗そ澄髅诺募依铩⒆×硕嗳铡

When he was a student, he also learnt Beijing Opera like Went Into The Palace Twice, which received good praises from audiences.

在校习艺时，曾兼学京剧，在《二进宫》、《铡美案》等剧演出时，颇受观众好评。

The cloud was roughly 6, 000 feet across and ultimately rose to a height of nearly 10, 000 feet before being dispersed.

云层直径大约6000?眨0当它还没有被风吹散以前，它将最后升达近1万?盏母呖铡?

Initially I think the shipping would be on a LCL basis (Less than Container Loads), although if the volume of orders justified it, possibly 20ft or even 40 ft container loads.

开始我想可能会是散货，但是要根据实际订单量来订，可能是20?展裆踔潦?0?铡

Blade-to-handle ratio. Does the blade look proportional to the handle?

刀与刀柄的比例－刀与刀柄成比例吗？

Main movements include twining head, straight-arm raise, thrust, cloud, upper cut, drag and chop.

常见动作有：缠头裹脑、刺刀、劈刀、撩刀、云刀、带刀。

The subassembly can have two blades, three blades, four blades or five blades or more.

刀片组分为两刀、三刀、四刀、甚至五刀以上。

Don't mess around with sharp knives!

不要摆弄刀口锋利的刀！

end mill gashing and radius grinder

端铣刀和侧面铣刀磨床

blade, for fitting into reamers

装配在铰刀上的刀片