Ancon

The Learning and the date of Birth/Death of Kong Anguo and Kong Zang;

孔安国及其孔臧的生卒与学术

Kong Anguo as well comes to Hejian and .

孔安国亦游学献书河间,是析清古文经籍流传的关键。

Since then Fu Sheng, Kong Anguo, Xianwang-Hejian, and Zhang Ba all dedicated their Shangshu.

东晋初梅赜献上题名为西汉孔安国传注的古文《尚书》,并立在博士学官。

"Upon proper alignment of mounting holes, the two bolts and washers should be installed."

安装孔对准后,应该把两个螺栓和垫圈安装上去。

Wheel Hub Installing Holes Parameter Test Based on CCD;

基于CCD的轮毂安装孔形位参数测量

"They are usually equipped with fixing bolt holes, internal or external gear, lubrication holes and sealing elements."

该产品一般都带有安装孔、内齿轮或外齿轮、润滑孔和密封装置

T&P relief valve opening - comes standard with special tapping on side of tank.

降温减压安全阀安装孔-作为标准配置,热水器侧面均有特制的安装孔。

Spark plug M10X1 with flat seating and cylinder head housing

GB/T6784-1986M10×1平座火花塞及其气缸盖安装孔

Screw hollow and motor spindle are distributed staggered and equally.

螺纹安装孔的位置与电装电机轴线成错开对称分布。

A. Position the bores according to the product. Drill φ 6 bores respectively with impact driller, after the center line for bolt bore is drawn in the appropriate position on the wall.

根据产品安装孔位，在墙面相应位置画出螺钉孔中心线后，用冲击钻分别钻φ6孔。

40L with test lever and short thermostat for installation directly in available tank tappings.

40L型号安全阀配置测试杆和较短的温控器,用于直接安装在容器安装孔上。

(British) a hole into which a plug fits (especially a hole where water drains away).

（英国）用来安装插头的孔（尤指排水孔）。

" Dimensions for the mounting of single-hole, bush-mounted, spindle-operated electronic components"

GB/T14120-1993单孔轴套安装、轴控电子元件的安装尺寸

THE INSTALLATION OF CONE-SHAPED PUNCH FOR WSP250 HOT-ROLLED

WSP250热轧钢管工程锥形穿孔机的安装

The controller is floor/Base plate mounted by using the three pre-drilled holes in each leg. The holes are dimensionally on the same line for ease of mounting.

控制装置是通过每个支柱的三个预钻孔安装在地面/底板上。这些孔位于同一条支线上,便于安装。

Assemble the thread stand unit, and insert it in the hole in the machine table.

如图所示那样组装线架装置，再安装到机台的孔上。

INSTALL BALLS IN THIS HOLE WHILE SLOWLY ROTATING WORM COUNTER CLOCKWISE

当逆时针缓慢转动蜗杆时在孔中安装锁球。

Position flywheel and O-ring on crankshaft and align bolt holes.

安装飞轮和O形环在曲轴上并对齐螺栓孔。

Precasting and Installation of the Double-Track Simply Supported Monolithic Box Beams of High-Speed Railroad;

高速铁路双线整孔简支箱梁的预制和安装

On Install Technique of GEOKON 4300 Vibrating Wire Stress Appearance;

振弦式孔应力仪在复合顶板中的安装技术分析

Installation of Working Radial Gate and Hydraulic Hoist of Bottom Sluice of Xiaowan Hydropower Station

小湾水电站放空底孔工作弧门及启闭机安装